Compact size, + DC frequency
100 Hz/120 Hz/1 KHz/10 KHz
Ls/Lp/Cs/Cp/Rs/Rp with D/Q/θ /ESR parameters
LCR METER
Model : LCR-9173
FEATURES
* 6000 counts ADC resolution. Capacitance ( Cp/Cs ) : D 0.1, 0.5V(rms≦ )
* Dual power supply , Battery or AC/DC Adapter.
* High performance analog front end for impedance Range Accuracy Accuracy
(Z) measurement. 100 Hz 120 Hz
* Support Z / DCR measurement for LCR mode. 600 pF ± ( 3.5% + 5d ) ± ( 3.5% + 5d )
* Four different test frequency are available : 6000 pF ± ( 2.5% + 5d ) ± ( 2.5% + 5d )
100 Hz/120 Hz/1 KHz/10 KHz for L/C/R measurement. 60 nF ± ( 2.0% + 5d ) ± ( 2.0% + 5d )
* Built-in simple DMM front end circuit to support 600 nF ± ( 2.0% + 5d ) ± ( 2.0% + 5d )
DCV / Freq. / Diode mode. 6000 nF ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
* Test AC signal level : 0.5 V rms typically. 60 uF ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
* Test range : ( ex. F = 1 KHz ) 600 uF ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
L : 600.0 uH to 60.00 H 6000 uF ± ( 2.5% + 5d ) ± ( 2.5% + 5d )
C : 600.0 pF to 600.0 uF 10 mF ± ( 3.5% + 5d ) ± ( 3.5% + 5d )
R : 60.00Ω to 20.00 MΩ
* Low battery voltage detector. Range Accuracy Accuracy
* Min. source resistance : 120Ω typical. 1k Hz 10 kHz
* 6 ratio resistor range used for LCR mode. 600 pF ± ( 2.5% + 5d ) ± ( 2.0% + 5d )
* Support buzzer sound driver with driving pattern 6000 pF ± ( 2.0% + 5d ) ± ( 1.5% + 5d )
& frequency selectable. 60 nF ± ( 2.0% + 5d ) ± ( 1.5% + 5d )
600 nF ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
GENERAL SPECIFICATIONS 6000 nF ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
Display LCD size：46.5 X 45.5 mm. 60 uF ± ( 1.5% + 5d ) ± ( 2.5% + 5d )
Test frequency 100 Hz/120 Hz/1 KHz/10 KHz 600 uF ± ( 2.5% + 5d ) -------------------
MODE L/C/R L/C/R Function selector 6000 uF ------------------- -------------------
Frequency selector 10 mF ------------------- -------------------
D/Q/θ selector Remark :
SER/PAL selector * Don't apply voltage larger than 30 V to input terminals.
DCV DCV/Freq./Diode selector * Discharge capacitor before measurement.
Dissipation factor 0.0000 to 1999 * If intend to obtain the accurate value, please test
Quality factor 0.0000 to 1999 the component.
θ measurement ± 90° into the " Pin terminals " ( 3-7, Fig. 1 ) or tested
Calibration Open/Short calibration via optional.
Data Hold Freeze the display reading SMD tester, SMDA-22 or SMD test clip, SMDC-21.
Power off Auto shut off saves battery life or
manual off by push button Inductance ( Lp/Ls ) : D ≦ 0.1, 0.5V(rms)
Operating 0℃ to 50℃
temperature Range Accuracy Accuracy Remark
Operating Less then 85% R.H. 100 Hz 120 Hz
humidity 600 uH ------------------- -------------------
Power Supply 006P DC 9V battery 6000 uH ------------------- -------------------
* Alkaline or Heavy duty type 60 mH ± ( 2.0% + 5d ) ± ( 2.0% + 5d )
DC 9V adapter input 600 mH ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
* AC/DC power adapter is optional. 6000 mH ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
Power DC 6 mA approximately 60 H ± ( 1.5% + 5d ) ± ( 1.5% + 5d ) After
consumption calibration
Dimension 151 x 78 x 43mm 200 H ± ( 2.5% + 5d ) ± ( 2.5% + 5d ) After
Weight 235 g * meter only calibration
Standard * Instruction manual..........1 PC
Accessories * Alligator clips..................1 PC Range Accuracy Accuracy Remark
Included 1k Hz 10 kHz
Optional SMD tester, SMDA-22 600 uH ± ( 2.5% + 5d ) ± ( 2.5% + 5d ) After
Accessories SMD test clip, SMDC-21 calibration
AC to DC 9V adapter 6000 uH ± ( 2.0% + 5d ) ± ( 2.0% + 5d )
60 mH ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
ELECTRICAL SPECIFICATIONS (23±5 ℃) 600 mH ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
6000 mH ± ( 1.5% + 5d ) ± ( 1.5% + 5d )
Resistance ( DCR ) 60 H ± ( 2.5% + 5d ) ------------------- After
calibration
Range Accuracy Remark 200 H ------------------- -------------------
60 Ω ± ( 1.5% + 5d ) After calibration Remark :
600 Ω ± ( 1.0% + 5d ) * Discharge inductor before measurement.
6000Ω ± ( 1.0% + 5d ) * If intend to obtain the accurate value, please test the
60 KΩ ± ( 1.0% + 5d ) component
600 KΩ ± ( 1.0% + 5d ) into the " Pin terminals " ( 3-7, Fig. 1 ) or tested
6000 kΩ ± ( 1.0% + 5d ) via optional
20 MΩ ± ( 1.5% + 5d ) After calibration SMD tester, SMDA-22 or SMD test clip, SMDC-21.
Resistance(Z) ( Rp/Rs ) 0.5V(rms)
Scale range configuration
Range Accuracy Accuracy Remark
100 Hz/120 Hz 1k Hz LCR mode
60 Ω ± ( 1.5% + 5d ) ± ( 1.5% + 5d ) After calibration Function Frequency Meas. Range Min.
600 Ω ± ( 1.2% + 5d ) ± ( 1.2% + 5d ) mode resolution
6000Ω ± ( 1.2% + 5d ) ± ( 1.2% + 5d ) Inductance 100/120Hz 60.00mH~200.0H 0.01mH
60 KΩ ± ( 1.2% + 5d ) ± ( 1.2% + 5d ) Ls / Lp 1kHz 6000uH~60.00H 1uH
600 KΩ ± ( 1.2% + 5d ) ± ( 1.2% + 5d ) 10kHz 600.0uH~6000uH 0.1uH
6000 kΩ ± ( 1.2% + 5d ) ± ( 1.2% + 5d ) 100/120Hz 60.00nF~10.00mF 0.01nF
20 MΩ ± ( 2.0% + 5d ) ± ( 2.0% + 5d ) After calibration Cs / Cp 1kHz 6000pF~600.0uF 1pF
10kHz 600.0pF~60.00uF 0.1pF
Range Accuracy Remark 100/120Hz 60.00Ω ~20.00MΩ 0.01Ω
10 kHz Rs / Rp 1kHz 60.00Ω ~20.00MΩ 0.01Ω
60 Ω ± ( 1.5% + 5d ) After calibration 10kHz 60.00Ω ~20.00MΩ 0.01Ω
600 Ω ± ( 1.2% + 5d ) DC resistance N/A 60.00Ω ~20.00MΩ 0.01Ω
6000Ω ± ( 1.2% + 5d )
60 KΩ ± ( 1.2% + 5d ) DMM mode
600 KΩ ± ( 1.2% + 5d ) Function mode Meas. Range Min. resolution
6000 kΩ ± ( 1.2% + 5d ) DCV 600.0mV~20.00V 0.1mV
20 MΩ ± ( 3.0% + 5d ) After calibration
Remark : * Don't apply voltage larger than 30 V to Frequency 6.000kHz~15.00MHz 1Hz
input terminals.
